Resin Driveway Maintenance

The polyurethanes used in our resin driveways are one of the most chemically resistant materials. Care should be taken in the early days of the install to not expose the surface to any chemicals.

It is also very important that, before the resin has cured, nothing touches the resin that can cause imprints, such as animal paws.

Resin bound surfaces installed with materials from Resin Mill are designed for pedestrian use and for light vehicle traffic. Surfacing installed with materials from Resin Mill should not be misused and care should be taken wherever possible to ensure normal use of the surface. 

Resin bound aggregates should be laid at a minimum 20mm depth for vehicles over 7.5 tonnes. Heavy goods vehicles shouldn’t park or manoeuvre on resin bound paving unless it has been allowed for in the thickness of the resin bound installation. 

Careful consideration should be taken when handling any hard objects near or on resin bound surfacing. These include gardening machinery, motorbike stands, car jacks, car parts and hard plant pots which could potentially cause damage if they are dropped on the resin bound or dragged across the surface. 

Resin bound surfacing can sometimes be marked by the crushing of individual pieces of gravel by exceptional point loading. This can include but is not limited to, gravel trapped in tyre treads, especially in areas of high use. 

Care should also be taken if vehicle maintenance is being carried out on the resin bound. Wooden planks should always be used under car jacks to spread the load. The resin bound surface should always be protected from any grease, oil or spillages of petrol or solvents. The chemicals in the latter would soften a tarmac base. If there is a spillage, the surface should be washed down straight away with lots of water to try to dilute and wash away the chemicals. If the surface is still firm, it can be used. 

To remove leaves, sand soil and such like materials from resin bound paving, it can be swept clean with a stiff brush. Hosing the resin surface down with clean water will also clean the paving. It is common that regular brushing and washing is the only maintenance required for resin bound surfacing. 

Staining can occur from tannings from debris if they are not cleaned away and lay on the resin surface for prolonged periods of time. Most stubborn stains and grime elements can be removed with a pressure washer (maximum 150 bar rating). A fan-type lance should be used, and it should be sprayed at a minimum of 200mm above the resin bound surface. Only cold water should be used on resin surfacing. 

If any chewing gum were to stick to your resin surface, it can be easily removed with freeze spray. Each piece of chewing gum should be hardened with the freeze spray and then gently scraped off with a suitable scraper. 

Resin surfacing is weed resistant and is treated with weed killer prior to the installation of the resin bound surface. However, it is not fully guaranteed to be seedling free. This is because of seed dispersal from animals and the weather. If seedlings do start to grow, they can be simply pulled out by hand, ensuring the root is pulled out with the weed. In the event the seedlings take root, they can be killed off with mild weed killer. If you are using a strong weed killer, make sure to water it down significantly. Strong weed killers that aren’t watered down could cause discolouration to the resin surface. 

Brake fluid is extremely corrosive to resin bound. If brake fluid lands on the paving, it should be removed straight away with warm water.

To limit the chance of damaging the surface of the resin bound area and avoid tyre marks, the steering wheel of a vehicle should not be turned whilst stationary. Dry steering can damage the surface and over time, cause the aggregate to crush and come loose from the surface. If there are tyre marks on the surface for any reason, they can be removed with a simple wipe down with white spirit and a wash with emulsifier and fan-assisted pressure washer.

To limit the chance of any tyre marks, do not turn the steering wheel of the vehicle whilst stationary. For whatever reason, if there are tyre marks on the surface, simply wipe down with white spirit and wash with emulsifier and a fan-assisted pressure washer.

Although our resin bound surface  reduces the chance of ice and slippages, it is wise to still take precautions. White rock salt can be used on the surface of the resin to remove ice and frost. Salt traces should be removed once the adverse weather has subsided.

Resin bound paving is designed for pedestrian use and light vehicle traffic. Driveways, car parks, and forecourts are all suitable uses for resin surfaces. Resin bound aggregates should be laid at a minimum 20mm depth for vehicles over 7.5 tonnes. Heavy goods vehicles shouldn’t park or manoeuvre on resin bound paving unless it has been allowed for in the thickness of the resin bound installation. 

Skips and other heavy objects should not be dragged across the surface. For protection of the  resin surface  from such objects, wooden planks can be used to spread the load. 

Care should be taken with all metal objects on the surface of the resin bound. This includes objects such as car jacks, motorbikes, and machinery. 

If you’re looking for resin products for your home or business, you can’t go wrong with Resin Mill.